Cisco Systems ASR 1006 Guía de inicio rápido

QUICK START GUIDECisco ASR 1006 Router1 Documentation and Resources2 Prepare for Installation3 Rack-Mount the Router4 Connect the Router to the Networ

10Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be easily attached to the rack-mount bracket

11Figure 6 Attaching the Cable-Management Bracket to the Cisco ASR 1006 RouterStep 3 Using the bottom rack-mount ear hole, insert the screw through ca

12Chassis Ground Connection InstallationBefore you connect power or turn on power to your router, you must provide an adequate chassis ground (earth)

13Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure an adequate chassis ground.This comp

14–Connect to the port using the RJ-45-to-RJ-45 cable and RJ-45-to-DB-25 DTE adapter or using the RJ-45-to-DB-9 DTE adapter.Figure 8 Management Ethern

15Install the Cables in the Cable-Management BracketNo specific card level cable-management will be provided on the SIP carrier cards. SPAs utilize th

16Step 2 Plug the power cable into the inlet.Note For additional AC power cable strain relief, secure the cable to the power supply handle by insertin

17WarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground con

18Note DC input power cables must be connected to the PDU terminal studs in the proper positive (+) and negative (–) polarity. In some cases, the DC c

19Figure 13 DC Power Supply Ground Studs and CablesStep 4 Ground the other end of the grounding wires to an appropriate grounding point at your site.S

21 Documentation and ResourcesDocumentation for the Cisco ASR 1000 Series Aggregation Services Routers documentation is online with the exception of

20Figure 14 DC Power Supply Terminal BlockCaution Before you continue to install the terminal block ground wires, stop and perform Step 5. To prevent

21Figure 15 DC Power Supply Terminal Block Positive and Negative Cable Lugs With Protective SleevingStep 4 For easier cable-management, insert the neg

22Figure 16 DC Power Supply Terminal Block Positive and Negative ConnectionsStep 5 Tighten the Kepnut screw to recommended torque of 18 in-lbs minimum

23Figure 17 DC Power Supply Terminal Block and Plastic CoverCaution Secure the wires coming in from the terminal block so that they cannot be disturbe

24Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is from a Cisco ASR1006 router. The other Cis

25During the boot process, observe the system LEDs. The STAT LED comes on immediately as yellow, then turns to green when the Cisco IOS is booted. The

26validate_package: SHA-1 hash: calculated 479a7d62:6c128ba8:3616b8da:93cb3224:5c1aeb34 expected 479a7d62:6c128ba8:3616b8da:93cb3224:5

27*Feb 19 17:34:27.361: % Error opening nvram:/ifIndex-table No such file or directory*Feb 19 17:34:28.235: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Ma

28 TFTP_SERVER: 172.27.55.254 TFTP_FILE: asr1000rp1-advipservicesk9.v122_33_xn_asr_rls0_throttle_20080114_045627.binUsing

29 Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Experimental Version 12.2(20080110:152728) [BLD-mcp_dev.MCP_CRYPTO_INCREM

32 Prepare for InstallationThis section contains information about tools and parts, warnings, site preparation information, and information for rack-

30Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVIPSERVICESK9-M), Experimental Version 12.2(20080110:152728) [BLD-mcp_dev.MCP_CRYPTO_INCREMENT

31Default settings are in square brackets '[]'.Basic management setup configures only enough connectivity for management of the system, exte

32hostname Routerenable secret 5 $1$6r./$U5wHcV3uRWkKWK/fap474.enable password testsline vty 0 4password testno snmp-server!ip routingno bridge 1no cl

33!interface GigabitEthernet0shutdownno ip addressdialer-list 1 protocol ip permitdialer-list 1 protocol ipx permit!end [0] Go to the IOS command prom

34PPC/IOS XE loader version: 0.0.3loaded at: 00800000 0CD2C004zimage at: 00807673 009B8E53initrd at: 009B9000 01006E53isord at: 01007

35Note Basic management setup configures enough connectivity for managing the system; extended setup will ask you to configure each interface on the s

367 After InstallationFollow the instructions in this section to replace field replaceable units (FRUs) after installation. The Cisco ASR 1006 Router

37Replace a Power Supply in a Cisco ASR 1006 RouterThis section provides instructions for removing and replacing the AC power supply and the DC power

38The second is after enabling console logging. Output is at the console (and in the log).6ru_perf2#conf Configuring from terminal, memory, or networ

39Figure 18 DC Power Supply Terminal BlockStep 6 Locate the power supply ground stud. Remove the earth ground (GND) cable from the power supply. For D

4Prepare for Rack-Mount InstallationBefore you begin the rack-mounting tasks:• Decide whether or not you want to front rack-mount or rear rack-mount t

40 Console logging: disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer

41Figure 19 Handling a SPATo install a shared port adpter into a SPA interface processor (SIP), follow these steps:Step 1 Before you begin, make certa

42Step 4 After the SPA is properly seated, fasten the SPA in place with the captive installation screws on either side of the SPA.Note The shared port

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0

44

5Step 4 Insert and tighten the black screws on one side. Figure 2 Front Rack-Mount Brackets for the Cisco ASR 1006 RouterStep 5 Repeat Step 1 through

6Figure 3 Cisco ASR 1006 Router Rear Rack-MountingStep 3 Insert and tighten the five screws. After the bracket is secured to the side of the chassis,

7Figure 4 Installing the Cisco ASR 1006 Router in a Four-Post Rack Note Because the rack-mount brackets support the weight of the entire chassis, be s

8Step 7 Align the mounting bracket holes with the rack post holes and attach the chassis to the rack. At this point, if there is a third person, then

9Figure 5 Installing the Cisco ASR 1006 Router in a Two-Post RackCaution If you are using a two-post rack, secure the rack to the floor surface to pre