Cisco Systems Network Device 2800 Manual de instalación Pagina 119
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7
Installing Network Modules in Cisco 2800 Series Routers
OL-5790-01
Installing Blank Panels over Empty Chassis Slots
Installing Blank Panels over Empty Chassis Slots
All empty chassis slots for network modules must be covered with blank panels. Blank panels are
required to ensure proper cooling airflow and to prevent electromagnetic interference. Figure 9 shows a
typical blank panel.
Figure 9 Typical Blank Panel
Blank Panels for Network Module Slots
The network module hardware kit for Cisco 2800 series routers contains two blank panels. Each blank
panel covers one single-wide network module slot.
Install blank panels over empty network module slots as follows:
• Single-wide slot—Attach a blank panel.
• Extended single-wide slot—Install an adapter/filler panel as described in the “Installing and
Removing Filler Panels in Network Module Slots” section; then attach a blank panel.
Related Product Documentation
The following documentation is related to your product. This documentation was not shipped with your
product, but you can access it online at Cisco.com.
• Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information
121064
- Introduction and Warnings 1
- Audience 2
- Conventions 3
- Safety Warnings 4
- Avvertenza 5
- Advarsel 5
- ¡Advertencia! 5
- Varning! 6
- Safety Warnings 8
- Related Documentation 9
- OL-5808-01 10
- Obtaining Documentation 11
- Documentation Feedback 12
- Submitting a Service Request 13
- Hardware Features 18
- OL-5783-01 19
- Hardware Features 19
- Built-in Interfaces 20
- LED Indicators 23
- Chassis Views 26
- 7 9 11 12 13 14 14 27
- Cisco 2811 Chassis 28
- Chassis Views 29
- 1457 6 3 30
- 6 4 3 75 31
- Interface Numbering 32
- Specifications 34
- Specifications 35
- Regulatory Compliance 41
- Regulatory Compliance 42
- Safety with Electricity 44
- General Site Requirements 45
- Site Environment 46
- Site Configuration 47
- Equipment Racks 47
- Installation Checklist 48
- Creating a Site Log 49
- Inspecting the Router 49
- OL-5784-01 51
- Console Port Connections 53
- Auxiliary Port Connections 54
- Ethernet Connections 55
- Serial Connections 55
- Signaling Standards Supported 56
- Distance Limitations 56
- ISDN BRI Connections 57
- CSU/DSU Connections 58
- Series Routers 59
- For HWICs and VICs: 60
- For AIMs 62
- For PVDMs 62
- For Internal Power Supplies 62
- Setting Up the Chassis 63
- OL-5786-03 64
- Setting Up the Chassis 64
- Use four screws on each side 65
- Chassis Grounding 68
- Statement 248 69
- Ring terminal 72
- Ground lug 72
- Routers” online document 73
- Power Connections 76
- DC Wiring Requirements 77
- Wiring Procedure for DC Input 78
- Statement 117 79
- 2800 Routers 80
- OL-5787-02 81
- Power Connections 81
- Ports and Cabling 84
- Checklist for Power Up 89
- Power Up Procedure 90
- Configuring the Router 92
- Completing the Configuration 97
- OL-5788-01 98
- Configuring the Router 98
- Normal Indications 100
- Fault Indications 100
- OL-5789-01 101
- Solving Problems 101
- Reading System LEDs 102
- • Router fault 103
- Reading Port and Module LEDs 104
- System Messages 105
- Recovering a Lost Password 109
- Corporate Headquarters: 113
- OL-5790-01 114
- 1 Filler panel 117
- 1 Slot divider 3 Filler panel 117
- 2 Blank panel 117
- Related Product Documentation 119
- OL-5791-01 122
- Slot divider flush 125
- Figure 7 Typical Blank Panel 126
- Cisco 2800 Series Routers 129
- Removing the Chassis Cover 130
- OL-5792-04 131
- Removing the Chassis Cover 131
- Statement 1003 132
- Statement 1041 132
- Screwdriver must not 133
- Plastic bezel 134
- Approx. 1 inch 134
- Locating Modules 137
- 3 PVDMs 7 Fans 138
- 4 Power supply 138
- 2 DRAM DIMMs 5 Fans 139
- Removing a DRAM DIMM 141
- Installing and Removing AIMs 144
- Software Requirement for AIMs 145
- AIM Location 145
- Removing an AIM 145
- Accessory Kit to Use 146
- Installation Procedure 146
- Metal standoffs 147
- Locking end 148
- Applying the AIM Label 154
- Verifying AIM Installation 155
- Installing and Removing PVDMs 156
- PVDM Location and Orientation 157
- Removing a PVDM 157
- Installing a PVDM 158
- Replacing the Power Supply 159
- Replacing the Power Supply 160
- 1 Power supply 3 Ribbon Cable 163
- 2 Retention screw location 163
- Cover” section on page 51 165
- Installing an ILP Supply 168
- Power supply 172
- 1 Primary power connector 173
- Installing the Chassis Cover 179
- OL-5793-01 184
Relacionado con productos y manuales para Redes Cisco Systems Network Device 2800
Redes Cisco Systems PI21AG Manual de usuario
(34 paginas)
(34 paginas)
Redes Cisco Systems OL-6030-01 Manual de usuario
(6 paginas)
(6 paginas)
Redes Cisco Systems 535 Manual de usuario
(24 paginas)
(24 paginas)
Redes Cisco Systems BC-109 Manual de usuario
(56 paginas)
(56 paginas)
Redes Cisco Systems OL-1375-02 Manual de usuario
(8 paginas)
(8 paginas)
Redes Cisco Systems MGX-FRSM-2T3E3 Manual de usuario
(54 paginas)
(54 paginas)
Redes Cisco Systems CATALYST 8500 Manual de usuario
(20 paginas)
(20 paginas)
Redes Cisco Systems XR 12410 Manual de instalación
(230 paginas)
(230 paginas)
Redes Cisco Systems Chassis AS5350 Manual de instalación
(102 paginas)
(102 paginas)
Redes Cisco Systems ASA 5500 Manual de usuario
(16 paginas)
(16 paginas)
Redes Cisco Systems OL-1377-02 Manual de usuario
(14 paginas)
(14 paginas)
Redes Cisco Systems SS7 Manual de usuario
(64 paginas)
(64 paginas)
Redes Cisco Systems ASR 1000 Manual de usuario
(112 paginas)
(112 paginas)
Redes Cisco Systems OL-7821-04 Manual de usuario
(131 paginas)
(131 paginas)
Redes Cisco Systems A9K24X10GETR Guía de inicio rápido
(142 paginas)
(142 paginas)
Redes Cisco Systems 2130 Manual de usuario
(116 paginas)
(116 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales