Cisco Systems 4/8xFE Guía de usuario Pagina 98
- Pagina / 131
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 6 Cabling the Line Ports and Completing the Installation
Installing a Cascaded System
Cisco SCE 2000 4/8xFE Installation and Configuration Guide
6-12 OL-7826-05
• Sniffing — allows the SCE platform to forward traffic on the specified link through the
bypass mechanism while still analyzing the traffic passively.
Sniffing is permitted to be configured for all links, only (use the all-links option).
• Cutoff — completely cuts off flow of traffic through the specified link.
Note the following recommendations and restrictions:
• Since the SCE 1000 platform has only one link, the link is not specified.
• Since the SCE 2000 platforms have more than one link, it is required to specify the link. The
link designations are different for the GBE and FE platforms, as follows:
• SCE 2000 4xGBE — GBE1-GBE2/GBE3-GBE4
• SCE 2000 4/8xFE — LINK1/LINK2
• Use the 'all-links' option to configure the link mode for all links (SCE 2000 platforms
only).
• It is recommended that both links be configured together. Use the all-links option.
• Link mode is relevant only to inline topologies.
• It is recommended that in cascaded topologies, both SCE platforms be configured for the
same link mode, otherwise the service will be unpredictable.
• Sniffing can only be configured for all links, therefore, to configure sniffing, the all-links
option is required, not just recommended.
• The default link mode is forwarding. When other link modes are selected, active service
control is not available and any service control configuration will not be applicable.
To set the link mode, use the following command:
From the SCE 2000 (config if)# prompt, type link-mode [<link>|all-links]
[forwarding|bypass|sniffing|cutoff] and press Enter.
Monitoring the System
Use the following commands to view the current connection mode and link mode parameters.
To view the current connection mode, use the following command:
From the SCE 2000# prompt, type show interface linecard 0 connection-mode
and press
Enter.
- Cisco SCE 2000 4/8xFE 1
- OL-7826-05 i 3
- Contents 4
- Preface 7
- Audience 8
- Organization 8
- Related Publications 9
- Conventions 10
- Obtaining Documentation 11
- Documentation Feedback 12
- Cisco.com 12
- Technical Assistance Center 12
- Contacting TAC by Telephone 13
- General Overview 15
- 1-2 OL-7826-05 16
- The SCE Platform 17
- Management and Collection 18
- Network Management 19
- Subscriber Management 19
- Data Collection 20
- Front Panel 21
- 2-2 SCE 2000 22
- 2-3 SCE 2000 23
- Back Panel 24
- 2-4 SCE 2000 25
- 2-5 SCE 2000 26
- Topology 27
- Functionality 28
- Number of links 28
- Redundancy 28
- Link Continuity 29
- Physical Topologies 30
- Chapter 3 Topology 31
- Physical Topologies 32
- Topology-Related Parameters 34
- SCE 2000 Configuration 35
- Priority 36
- On-Failure Mode Parameter 36
- Installation and Maintenance 37
- Tools and Parts Required 38
- Site Requirement Guidelines 39
- 4-3 SCE 2000 40
- Installation Precautions 41
- 4-6 OL-7826-05 42
- OL-7826-05 4-7 43
- 4-8 OL-7826-05 44
- OL-7826-05 4-9 45
- 4-10 OL-7826-05 46
- Power Supply Overview 47
- 4-12: AC Power Module 48
- 4-13: DC Power Module 48
- OL-7826-05 4-13 49
- Power Supply Specifications 50
- OL-7826-05 4-15 51
- DC-Input Leads 52
- Reconnecting the Power 53
- 4-18 OL-7826-05 54
- OL-7826-05 4-19 55
- Fan Module Overview 56
- Replacing the Fan Module 57
- Replacing the Battery 58
- Connecting the Local Console 59
- Setting Up the Local Console 60
- Initial System Configuration 61
- 5-4 OL-7826-05 62
- 5-6 OL-7826-05 64
- Enter hostname [SCE 2000]: 65
- 5-8 OL-7826-05 66
- OL-7826-05 5-9 67
- 5-10 OL-7826-05 68
- OL-7826-05 5-11 69
- 5-12 OL-7826-05 70
- Entry Formats 71
- Order of Entries 71
- 5-14 OL-7826-05 72
- OL-7826-05 5-15 73
- Step 8: Configuring SNMP 74
- OL-7826-05 5-17 75
- 5-18 OL-7826-05 76
- 5-20 OL-7826-05 78
- OL-7826-05 5-21 79
- 5-22 OL-7826-05 80
- OL-7826-05 5-23 81
- 5-24 OL-7826-05 82
- OL-7826-05 5-25 83
- Cabling the Management Port 84
- OL-7826-05 5-27 85
- Installation 87
- Cabling Diagrams 88
- OL-7826-05 6-3 89
- 6-4 OL-7826-05 90
- OL-7826-05 6-5 91
- Cabling the FE Line Port 92
- Examining the Link LEDs 93
- 6-8 OL-7826-05 94
- Installing a Cascaded System 95
- 6-10 OL-7826-05 96
- Link Mode 97
- Monitoring the System 98
- OL-7826-05 6-13 99
- OL-7826-05 7-1 101
- 7-2 OL-7826-05 102
- Final Tests 103
- Viewing Configuration 104
- OL-7826-05 7-5 105
- 7-6 OL-7826-05 106
- Step 3 Type 107
- 7-8 OL-7826-05 108
- OL-7826-05 7-9 109
- Displaying the System Uptime 110
- OL-7826-05 7-11 111
- Troubleshooting 113
- Troubleshooting Tools 114
- OL-7826-05 8-3 115
- The User Log 116
- Copying the User Log 117
- Viewing the User Log 117
- Clearing the User Log 117
- Troubleshooting Tools 118
- Check the LEDs 119
- Identifying Startup Problems 120
- OL-7826-05 8-9 121
- 8-10 OL-7826-05 122
- OL-7826-05 8-11 123
- 8-12 OL-7826-05 124
- OL-7826-05 8-13 125
- 8-14 OL-7826-05 126
- Auto-negotiation is disabled 127
- OL-7826-05 I-1 129
- Index 130
- OL-7826-05 I-3 131
Relacionado con productos y manuales para Redes Cisco Systems 4/8xFE
Redes Cisco Systems MGX 8000 Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales