Cisco Systems PGW 2200 Guía de usuario Pagina 330
- Pagina / 436
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
A-18
Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide
OL-18083-01
Appendix A XECfgParm.dat File Parameters
Understanding the XECfgParm.dat File Format
*.SUA.maxOPCs Defines the maximum number of SUA OPCs.
Val ue : 64
Note Do not change this value.
*.SUA.maxRoutesPerOpcApcSsn Defines the maximum number of SUA routes per OPC,
adjacent point code (APC), and subsystem number (SSN)
set.
Val ue : 2
Note Do not change this value.
*.SUA.maxSgp Defines the maximum number of SUA SS7 signaling
gateway processes.
Val ue s: 8
Note Do not change this value.
*.SyscheckpointEnabled Enables or disables checkpointing.
Values:
• false—Disables checkpointing. Calls are not preserved
during a switchover, and status messages are not sent to
the replicator (default).
• true—Enables checkpointing. Calls that are in the
talking state are preserved and survive a control
switchover. All status checkpointing information is sent
to the replicator on the active side.
Default: false
Note If you have two Cisco PGW 2200 Softswitch hosts
in a failover configuration, enter true. If you have a
standalone configuration, enter false.
*.SysConnectDataAccess Controls whether data access is enabled or disabled (if the
engine attempts to connect to the MMDB or to call screening
database at startup).
Val ue s:
• true—Connect to MMDB or call screening database.
• false—Do not connect to MMDB or call screening
database.
Default: false
Note This parameter must be set to true in calling
scenarios where Euro-LNP, A Number Screening, or
other features requiring real time database access are
required. Otherwise, it can remain false for an
increase in the available system memory usable for
call processing.
Table A-1 Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Configuration Parameters
Configuration Parameter Definition
- Text Part Number: OL-18083-01 1
- CONTENTS 3
- Contents 4
- Document Objectives 9
- Audience 9
- Related Documentation 9
- Document Change History 10
- Installation 11
- Required Software Media 12
- Minimum System Requirements 12
- Required Tasks 13
- Table 1-4 Tasks Checklist 14
- Supported Platforms 15
- Supported Disk Drives 15
- Before You Start 16
- - Selecting package (SUNWifp) 20
- Host” section on page 2-50 26
- 89 blocks 34
- 426 blocks 34
- 8 blocks 34
- SUNWnfscr 43
- SUNWkrbr 43
- /devices-/devicesdevfs-no 45
- Configuring Your Host 64
- SUNWnfscr 85
- SUNWnisu 85
- DO NOT REBOOT 100
- OL-18083-01 104
- (CSCOh026) 117
- Using the SunVTS Test Package 145
- Normal Unit Test 145
- Running a Test in Brief Mode 149
- Running a Test in Full Mode 150
- Manager (ILOM) 152
- Figure 2-1 System Agreement 153
- Figure 2-4 LOM Screen 154
- Start ILOM Using Secure HTTP 157
- An Example of Using ILOM 161
- Serial Console ttya 162
- Cautions, Notes, and Tips 166
- Enter y and press Enter 169
- Enabling Sudo 179
- Installing the License File 179
- Software 183
- Software Directory Structure 185
- % MGC_Setup 190
- Configuring Groups and Users 193
- Basic Tasks 196
- Deleting an SNMP COMMUNITY 201
- Adding a Trap Destination 202
- Deleting a Trap Destination 204
- Activating the New Settings 205
- Specifying IP Addresses 212
- Configuring Engine Parameters 214
- Setting the Call Cutoff Timer 216
- Enabling Call Screening 216
- Configuring Switchover 221
- Configuring SCP Queries 224
- Sample trigger.dat File 227
- .odbc.ini File Information 265
- Setting Up Replication 265
- Network Requirements 266
- Synchronizing Databases 270
- Configuring Cisco ITP-Ls 271
- Configuring the Data Dumper 272
- Migrating to Solaris 10 and 275
- Release 9.8 275
- Cautions and Notes 276
- Required Software 277
- License Installation 277
- Recording System Data 277
- Migration Overview 278
- Installing Sun Solaris 10 282
- Restoring Data Files 283
- Platforms 295
- Live Upgrade Procedure 296
- Falling Back Overview 300
- Release 9.5 or 9.6 301
- Backup Procedure 308
- Restoring the System 309
- LAN Switch Overview 311
- Catalyst 2900 XL Series 312
- Catalyst 5500 and 5000 Series 312
- XECfgParm.dat File Parameters 313
- Special Parameters 314
- Relationships 359
- HP OpenView 363
- Formatting Trap Messages 365
- Step 8 Close the window 366
- Sample Installation Scripts 367
- Sample Uninstall Scripts 413
- Sample LAN Configurations 421
Relacionado con productos y manuales para Software Cisco Systems PGW 2200
Software Cisco Systems OL-5532-02 Manual de usuario
(32 paginas)
(32 paginas)
Software Cisco Systems 2200 Manual de usuario
(134 paginas)
(134 paginas)
Software Cisco Systems QC-29 Manual de usuario
(24 paginas)
(24 paginas)
Software Cisco Systems OL-25712-04 Manual de usuario
(768 paginas)
(768 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales